أمبير محول 75 كيلو فولت أمبير: دليل التيار الابتدائي والثانوي

75 kVA Full-Load Amps by Voltage and Phase

The table below uses a 75,000 VA nameplate rating. For three-phase rows, voltage means line-to-line voltage and current means line current. Single-phase rows use the voltage across the winding. Values are rounded to one decimal ampere; the design calculation should use the actual nameplate voltage and the project electrical drawings.

This table is a current lookup, not a promise that every 75 kVA transformer is available in every listed voltage or connection. Confirm the actual primary and secondary nameplate ratings, winding connection, frequency, taps and cooling designation. Never use a 400 V row for a 480 V winding simply because both are described as industrial three-phase systems.

Worked Example: 480 V Primary to 208Y/120 V Secondary

Consider a balanced 75 kVA, three-phase step-down transformer with a 480 V line-to-line primary and a 208Y/120 V secondary. On the primary, the theoretical full-load line current is 75,000 ÷ (√3 × 480) = 90.2 A. On the secondary, it is 75,000 ÷ (√3 × 208) = 208.2 A. The 120 V marking identifies line-to-neutral voltage on the wye secondary. For the three-phase calculation, use 208 V line-to-line, not 120 V.

The higher secondary current is expected: voltage falls while apparent power remains approximately the same, allowing for real transformer losses. When reviewing a one-line diagram, calculate each side separately. Check the transformer nameplate before ordering a breaker or cable; current alone does not establish conductor ampacity, breaker setting or short-circuit duty.

How Many kW Can a 75 kVA Transformer Supply?

kVA measures apparent power; kW measures real power. For a balanced load, estimated real power is kW = 75 × power factor. At 0.8 power factor, that is 60 kW. At 0.9 power factor, it is 67.5 kW. At unity power factor, the mathematical maximum is 75 kW. These figures do not replace a load study: harmonics, motor starting, duty cycle, ambient temperature and the transformer’s actual thermal rating still matter.

Do not apply an automatic “80% of 75 kVA” rule to every transformer. A continuous-load rule for a particular protective device or installation is not the same as the transformer’s nameplate thermal capacity. Ask the electrical designer to document the applicable code, manufacturer instructions, load profile and required spare capacity.

When 75 kVA Is Too Small

Compare the highest expected coincident demand in kVA with the transformer’s rating under the actual operating conditions. If several loads start at different times, a simple sum of every nameplate rating may overstate demand. If large motors start together, steady-state current can understate the short-duration voltage dip. Record both cases rather than treating a single amperage number as the entire sizing decision.

For example, a balanced 480 V three-phase load drawing 100 A represents approximately √3 × 480 × 100 ÷ 1,000 = 83.1 kVA before any allowance for expansion. That exceeds 75 kVA. Conversely, a 60 A load at the same voltage represents about 49.9 kVA, leaving apparent-power headroom, subject to starting current, thermal conditions and other connected loads. Schneider Electric’s capacity guidance explicitly notes that motor and specialty loads may require more than the simple arithmetic result.

What to Send With a 75 kVA Transformer Inquiry

Give the supplier the primary and secondary voltage, phase, frequency, connection, installation site, required enclosure, ambient conditions and available fault current. Include the load schedule, motor-starting information, harmonic-producing equipment and space limits. Ask for a data sheet showing nameplate ratings, impedance, losses, temperature rise, dimensions and routine test documents. If replacing a unit, provide photos of the existing nameplate and terminal layout, not only the phrase “75 kVA transformer.”

For adjacent calculations, use our 63 kVA load-capacity example, amps-to-kVA formula guide و دليل صهرات المحولات. Review the مجموعة منتجات المحولات for available configurations; confirm project-specific values with the manufacturer.

Three-Phase Transformer Video Lesson

For the relationship between phase voltage, line voltage and transformer connections, this NPTEL university lecture provides a useful technical introduction. The calculation table above remains the direct answer for 75 kVA current.

Watch NPTEL’s Introduction to Three Phase Transformer on YouTube.